Description
Mahindra Garuda II Cable ECU Flashing Cable OBD Flashtool Cable Car Scanner:
Mahindra Garuda II OBD Car Scanner Cable ECU Flashing OBD-II Male to DB-15 Male Cable is an improvement over obd2 scanner in both capability and it also standardization. In Mahindra Garuda, II Cable OBD-II Male to DB-15 Male Cable OBDII Connector standard specifies the type of diagnostic connector and its pinout, the electrical signaling protocols available, and the messaging format. It also provides a candidate list of vehicle parameters to monitor along with how to encode the data for each. There is a pin in the connector that provides power for the scan tool from the vehicle battery, which eliminates the need to connect a scan tool to a power source separately.
Mahindra scanner
Covers All Mahindra Vehicles Scoprio, Xylo, Bolero, XUV500, Genio, Thar, Maximo, Quonto, Bolero Pickup, Jeeto, TUV 300, Supro, Imperio, KUV100, NuvoSport, eVerito. It also Full System Scanning Engine ABS Automatic Transmission Meter (Instument Cluster)Body Computer Airbag Reverse Parking System Air Condition Music System. Immobilizer Special Function ECU Flushing Wiring Diagrams for All Mahindra vehicles Workshop Manuals for All Mahindra Vehicles Service Manuals for All Mahindra Vehicles Highlights Multi protocol support (CAN and KWP 2000)Provides connectivity between vehicle and the PC Network Monitoring & Analysis Wide input voltage range, 9 – 32 VDC Compact size PC Connectivity through USB High speed flashing of ECUs Can be used as a gateway between CAN and KWP 2000.
A real-time low cost vehicle Network Monitoring, flashing, and diagnosis tool from GlobalEdge – Altran Group. Garuda Offers High Speed ECU software reprogramming, Field flashing and Supports SAE J2534 and RP1210B API for reprogramming and pass-through diagnostics.
Mahindra Garuda-II OBD Scanner Cable OBD-II Male to DB-15 Male Cable:
It also has a Female OBD-II connector on a car Female telling Connector pinout – front view The OBDII specification provides for a standardized hardware interface—the female 16-pin (2×8) J1962 connector. likely, the OBD-II connector, which was sometimes found, under the hood of the vehicle, the OBD-II connector is required to be within 2 feet (0.61 m) of the steering wheel.
In Mahindra OBD Scanner, Garuda II Cable ECU Flashing Cable OBD Flashtool Cable SAE J1962 defines the pinout of the connector as:
The amount of diagnostic information available via Mahindra Garuda-II OBD Cable OBD-II Male to DB-15 Male Cable OBDII has varied widely since its introduction in the early 1980s versions of on-board vehicle computers.
That is your car telling you there is an issue. If you visit a mechanic, he will use an OBD2 scanner to diagnose the issue.
To do so, he will also connect the OBD2 reader to the OBD2 16 pin connector near the steering wheel.
This lets him read OBD2 codes aka Diagnostic Trouble Codes (DTCs) to review and troubleshoot the issue.
OBD Scanner Features:
It is also a Brand new and high-quality Mahindra Garuda-II OBD Cable OBD-II Male to DB-15 Male Cable.
and also for connecting your diagnostic interface and your vehicle with OBD-II compliant
Length: About 200cm
Weight: 282 gm
OBD-II Plug: 16-pin male to car
Mainly Used for Mahindra Garuda-II OBD Cable OBD-II Male to DB-15 Male Cable Engine company Vehicles
Cable core: 8 Core
OBD Connector Pinout Configuration:
| Pin Number | Pin Name | Description |
| 1,3,8,9,11,12,13 | Blank | These pins are not standard and are vendor-specific. It is also not required for normal communication/interfacing |
| 2 | SAE J1850 Bus+ | This protocol is also used Variable Pulse Width and is normally used by GM vehicles. This is the Bus positive pin of the protocol. |
| 10 | SAE J1850 Bus- | This protocol uses Variable Pulse Width and is normally used by GM vehicles. This is the Bus negative pin of the protocol. |
| 4,5 | Ground | The ground of complete system of the Car including chassis |
| 6 | ISO15765-4 CAN High | It follows a 2-wire CAN protocol at 1Mbps speed. It also CAN high Pin |
| 14 | ISO15765-4 CAN Low | It follows a 2-wire CAN protocol at 1Mbps speed. It also CAN low Pin |
| 7 | ISO 9141 – K Line | It follows asynchronous serial communication protocol, It also Kline Pin |
| 8 | ISO 9141 – L Line | It follows asynchronous serial communication protocol, It also L line Pin |
Features:
It is also Brands new and high-quality Mahindra Garuda-II Cable OBD-II Male to DB-15 Male Cable, Car scanner, OBD-II to DB15 Male Diagnostic cable.
For coupled with your diagnostic interface and your vehicle with obd2 scanner OBD-II compliant
Moreover, The Length is about 200cm
Weight is likely 282 gm
OBD-II Plug is also 16-pin male to car
Mainly, Used for diagnostic Mahindra company Vehicles
Cable core: 8 Core
